7 Mounting Stroboscope To mount the strobe on a tripod (or any other mounting surface), use screw ¼ -20unc, length 8mm or shorter for the trip
8 True RPM Measurement Shimpo Stroboscopes are DUAL function instruments that give the operator the illusion of “stopped motion” where in actualit
9 Internal Triggering Mode To use the DT-900 stroboscope in internal triggering mode: 1. Turn power switch on. 2. Press “MODE” button and the p
10 Phono Style Connector Information: The phono connector is 3.5mm in diameter size. Stereotype tip, it is the signal output from the strobe and
11 6. If the “x2” or “÷2” buttons are pressed and the calculated rate is beyond the range of 40-12,500 FPM, the flash rate will be set to the limit
12 Tachometer Mode In Tachometer Mode the strobe will not flash but can be used like a Shimpo handheld tachometer. The DT-900 Techstrobe will disp
13 Flash Tube Replacement When FPM reading is displayed but unit is not flashing, flash tube may need to be replaced: WARNING: The surface of t
14 1. Remove the front lens from the strobe by inserting the tip of a pen, screwdriver or similar device into one of the vent holes. Gently pry th
15 Charging the Battery If the battery is low, the stroboscope will not turn on completely and the display will eventually disappear. It is reco
16 4. The LED indicator on the handle will light up, indicating the battery is charging. Normal charging time is within 2 to 4 hours. It is strong
17 Troubleshooting FPM reading is displayed but unit is not flashing: Flash tube may need to be replaced (See Flash tube replacement section) S
18 Appendix Dimensions Battery Pack Dimensions are in Inches, unless otherwise specified.
19 Dimensions DT-900 Dimensions with Battery Pack Dimensions are in Inches, unless otherwise specified
20 Phono Connector DT-900 Phono Jack Information Phono Connector Description DT-900 Size 3.5mm Type Stereo Signal Input Tip Signal Output Rin
21 Accessories Part Number Description FLASHTUBE900 FLASH TUBE REPLACEMENT DT-900 DT-900-1 REPLACEMENT BATTERY DT-900 DT-900-2 120V AC
22 DT-900-1 Replacement battery for DT-900. DT-900-2 120V AC 60 HZ, AC Adapter DT-900-6 Holster,
23 Mode Displays LOW BATTLOW BATTLOW BATTLOW BATT 1200.01200.01200.01200.0 Message RPM TachModTachModTachModT
24 Application Pictures ROTATIONAL SPEED OF SHAFT WITH THE USE OF AN INDICATOR MARK YOU CAN FREEZE AND CHECK THE SPE
25 CHAIN INSPECTION /RPM DRILL INSPECTION/RPM
26 ROTATIONAL SPEED OF MOTOR GAP INPSECTION OF ROTOR AND STATOR, THIS IS GOOD FOR QC/QA NOISE REDUCTION AND ISPECTION OF DAMAGE DUE
Table of Contents Introduction . . . . . .. …………………………………………………………………………………….1 Features Safety Warning……………………………………………………………………………………………
27
28
29
1 Table of Contents OPERATIONS MANUAL INTRODUCTION Thank you for purchasing this Shimpo product. This manual explains how to operate your equ
2 For Safety and proper operation, please read this manual carefully. For additional information please call Shimpo Instruments at (800) 8
3 This equipment is free of defects prior to shipment; each strobe is tested and checked to guarantee proper operation. Repairs beyond changin
4 Each package should contain the following in addition to the DT-900 Stroboscope. • Charger • Spare lamp Additional parts such as sensor
5 Do not store instrument on the following places • Explosive or combustible areas • Near water, oil, dust and chemicals. • Areas where tempera
6 Easy tab for Battery Pack removal External triggering connector Battery Pack Rechargeable Power Button Adjustment Dial Mode Contr
Commentaires sur ces manuels